Page History
Created date作成日Updated date | 更新日 | Affects version影響を受けるバージョンFix version | 修正バージョン |
---|---|---|---|
|
| Drive Eraser - all全て | N/A |
Description
Apple branded SSD with disk model SMxxxxF SSDs (where xxxx represents the capacity of the disk) is no longer detected by the device and can no longer be used after the erasure.
Issue is known to happen with following combination of disk model and disk firmware versions:
問題事象
AppleブランドのSSDがデータ消去後に使用できない状態になる。該当するSSDは「SMxxxxF」という機種名をもち、「xxxx」の部分は容量に対応します。
この事象が発生したディスクモデルとディスクファームウェアバージョンの組み合わせは次の通りです。
ディスクモデルKnown affected disk models:
- APPLE SSD SM1024F
- APPLE SSD SM0512F
- APPLE SSD SM0256F
- APPLE SSD SM0128F
Known affected firmware versionsファームウェアバージョン:
- UXM6JA1Q
- UXM2JA1Q
- UXM2EA1Q
Below table lists some of the affected system models were you can expect to see this issue. Please note that this is not full list of affected hardware and it is possible to see this issue with models not listed below.
以下の表に問題が発生するシステムモデルの一部を示します。掲載されていないモデルでも発生する可能性があることに注意してください。
ディスクモデル | システムメーカー | システムモデル | ディスクファームウェアバージョン | Disk model | System manufacturer | System model | Disk firmware revision |
---|---|---|---|---|---|---|---|
APPLE SSD SM0256F | Apple Inc. | MacBookAir6,1 | UXM2JA1Q | ||||
APPLE SSD SM0512F | Apple Inc. | MacBookAir7,2 | UXM2JA1Q | ||||
APPLE SSD SM0256F | Apple Inc. | MacBookPro11,1 | UXM2JA1Q | ||||
APPLE SSD SM0512F | Apple Inc. | MacBookPro11,2 | UXM2JA1Q | ||||
APPLE SSD SM1024F | Apple Inc. | MacBookPro11,3 | UXM6JA1Q | ||||
APPLE SSD SM0512F | Apple Inc. | MacBookPro12,1 | UXM2JA1Q | ||||
APPLE SSD SM1024F | Apple Inc. | iMac14,2 | N/A |
Cause
This issue is caused by non-standard firmware available on these SSDs. Affected drives are not capable of executing "Secure Erase" or "Enhanced Secure Erase" firmware based commands properly, which leads to a scenario where the disk is no longer being detected after these command have been executed.
Resolution
...
原因
該当するSSDの非標準的なファームウェアが原因です。ファームウェアベースのコマンドである「Secure Erase」と「Enhanced Secure Erase」を適切に実行されないため、コマンドの後に検出されなくなってしまいます。
解決策
この問題の発生を防ぐためにはSecure EraseとEnhanced Secure Eraseを使用しない消去設定をお勧めします。これはたとえばNIST 800-88 Purgeを使用して実現できます。
Info |
---|
Drive EraserのNIST 800-88 PurgeからNIST 800-88 Clearへの自動フォールバック機能を利用している場合も、ファームウェアベースのコマンド「Secure Erase」がNIST 800-88 Clearの最中に実行されて当事象が発生します。 この場合、ファームウェアベースのコマンドを使わない消去規格(Aperiodic Random Overwrite等)を指定することを推奨します。 |