Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

USB接続の外付けドライブを消去するときは、消去処理中に問題が発生しないように、以下の推奨事項に従ってください。

  1. 消去オプション:
    • 一般的に、外付けUSBドライブはケース内のSATAドライブで構成され、マシンとの通信は内部のUSB-to-SATAアダプターを介して実行されます。ほとんどのアダプターは、SATAドライブに読み取り/書き込みコマンドを渡すことができますが、ファームウェアコマンドを正しく渡すことはできません。したがって、「NIST 800-88 Purge」や「Blancco SSD Erasur」のような消去規格は、これらのデバイスでは失敗する傾向があります。そのため、これらのドライブの消去には通常の上書き規格を使用すると同時に、消去オプションの「SSDにBlancco SSD 消去方式を強制」、「リマップセクターのデータを消去」、「隠し領域を解除」を無効にすることをお勧めします。
  2. レポートのバックアップ:
    • 消去ステーションで複数のドライブを消去する場合は常に、完了した消去のレポートをすぐに保存するために、Drive Eraser Configuration Toolを使用して、 「自動レポートバックアップ」機能を有効にすることをお勧めします。
  3. ドライブの一括処理:
    • 一括して消去する場合には、類似した容量と製造元のUSBドライブで行うことをお勧めします 同じくらいの容量のドライブを一括処理にすることで、ほぼ同時に処理されます。.
    • また、USB 2.0のドライブ消去はUSB 3.0のドライブとは別処理にします。

When erasing external USB drives, follow below recommendations to prevent any issues during the erasure process.

  1. Erasure options:
    • Generally speaking, USB external drives consist of SATA drives within a case, the communication with the machine is performed through an internal USB-to-SATA adapter. Most adapters can pass read/write commands to the SATA drive but cannot pass properly firmware commands. Therefore, erasure standards such as "NIST 800-88 Purge" or "Blancco SSD Erasure" tend to fail on these devices. It is advised to erase these drives using normal overwriting standards as well as to disable the erasure options "Enforce Blancco SSD method on SSDs", "Erase remapped sectors" and "Remove hidden areas".
  2. Report backup:
    • Whenever erasing several drives in an erasure station, it is always recommended to enable the "Automatic report backup" feature (via the Drive Eraser Configuration Tool) to store immediately the report of any completed erasure.
  3. Drive batches:
    • It is advised to erase batches of USB drives having similar capacities and manufacturer. Having batches of drives of similar sizes will ensure that they are processed roughly at the same time.
    • Also, erase USB 2.0 drives in different batches than USB 3.0 drives.
  4. Do not hurry to refresh (applicable only if the hotswap feature is enabled):
    • When connecting a new drive, wait for a few seconds (5-10) before pressing the "Refresh drive list" button. This will allow the system to detect the drive properly before it is displayed in the UI.
    • In addition, if you don't see your newly connected drive after refreshing the list, do not rush into pressing the button again: some drives are slower than others and the detection can take up to a few minutes (on rather rare occasions).
  5. Refresh frequency (applicable only if the hotswap feature is enabled):
    • You can disconnect a drive, connect a new one then press the "Refresh drive list" button. However, the drive detection/display is faster if you refresh the drives after connecting/disconnecting a drive (e.g. disconnect -> refresh -> connect -> refresh).
  6. USB hubs:
    • If you use USB hubs, make sure that they are powered hubs. Keep in mind that erasing N USB drives connected to a hub will divide the erasure speed by N approximately. Therefore, it is advised not to use USB hubs but to connect directly the drives to the USB ports of the machine.
  7. Simultaneous erasures:
    • It is recommended not to erase more than 8 drives simultaneously. The maximum amount of drives you can erase also depends on your machine/erasure station specifications (processor, RAM, Motherboard, number of native USB ports, etc.).
  8. It is always recommended to use anti-static wrist strap to prevent electrostatic discharges (which can be a cause of hardware failures).

...