You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 2 Next »

USB接続の外付けドライブを消去するときは、消去処理中に問題が発生しないように、以下の推奨事項に従ってください。

  1. 消去オプション:
    • 一般的に、外付けUSBドライブはケース内のSATAドライブで構成され、マシンとの通信は内部のUSB-to-SATAアダプターを介して実行されます。ほとんどのアダプターは、SATAドライブに読み取り/書き込みコマンドを渡すことができますが、ファームウェアコマンドを正しく渡すことはできません。したがって、「NIST 800-88 Purge」や「Blancco SSD Erasur」のような消去規格は、これらのデバイスでは失敗する傾向があります。そのため、これらのドライブの消去には通常の上書き規格を使用すると同時に、消去オプションの「SSDにBlancco SSD 消去方式を強制」、「リマップセクターのデータを消去」、「隠し領域を解除」を無効にすることをお勧めします。
  2. レポートのバックアップ:
    • 消去ステーションで複数のドライブを消去する場合は常に、完了した消去のレポートをすぐに保存するために、Drive Eraser Configuration Toolを使用して、 「自動レポートバックアップ」機能を有効にすることをお勧めします。
  3. ドライブの一括処理:
    • 一括して消去する場合には、類似した容量と製造元のUSBドライブで行うことをお勧めします 同じくらいの容量のドライブを一括処理にすることで、ほぼ同時に処理されます。.
    • また、USB 2.0のドライブ消去はUSB 3.0のドライブとは別処理にします。
  4. Do not hurry to refresh (applicable only if the hotswap feature is enabled):
    • When connecting a new drive, wait for a few seconds (5-10) before pressing the "Refresh drive list" button. This will allow the system to detect the drive properly before it is displayed in the UI.
    • In addition, if you don't see your newly connected drive after refreshing the list, do not rush into pressing the button again: some drives are slower than others and the detection can take up to a few minutes (on rather rare occasions).
  5. Refresh frequency (applicable only if the hotswap feature is enabled):
    • You can disconnect a drive, connect a new one then press the "Refresh drive list" button. However, the drive detection/display is faster if you refresh the drives after connecting/disconnecting a drive (e.g. disconnect -> refresh -> connect -> refresh).
  6. USB hubs:
    • If you use USB hubs, make sure that they are powered hubs. Keep in mind that erasing N USB drives connected to a hub will divide the erasure speed by N approximately. Therefore, it is advised not to use USB hubs but to connect directly the drives to the USB ports of the machine.
  7. Simultaneous erasures:
    • It is recommended not to erase more than 8 drives simultaneously. The maximum amount of drives you can erase also depends on your machine/erasure station specifications (processor, RAM, Motherboard, number of native USB ports, etc.).
  8. It is always recommended to use anti-static wrist strap to prevent electrostatic discharges (which can be a cause of hardware failures).

Some additional information about the erasure of external hard drives can be found from this knowledge base article: 外付けハードドライブ (USB、eSATA、FireWire) および外付けドライブドッキングステーションでの消去

  • No labels